How Deep Can GPR See?

How deep can GPR see? It depends on what you’re scanning. In concrete, ground penetrating radar typically maps rebar, post-tension cables and conduits through the working depth of most slabs, walls and footings, often up to about 18 to 24 inches (45 to 60 cm). In soil, it can reach a few metres in dry, sandy ground, but much less in wet clay.

The real answer comes down to two things: the antenna we use and the material the signal travels through. Here’s how it works, and what it means for your job.

Typical GPR depths

Material

Typical depth range

Notes

Concrete slabs, walls and footings

Up to about 16–20 in (40 – 50 cm)

Depends on antenna, moisture and rebar density

Dry sand and gravel

2–4 m or more

Best conditions for GPR in the ground

Mixed soils, typical Lower Mainland sites

About 1–3 m

Varies across a single site

Wet clay or silt

Under 1 m in some areas

Clay absorbs the radar signal

Salty or saturated ground near the ocean

Shallow

Salt water strongly limits depth

These are typical ranges, not guarantees. Every site is different, and your technician will tell you on site what depth the scan is reaching.

Why depth changes: the antenna

GPR antennas work at different frequencies, and each one is a trade-off.

  • High-frequency antennas see fine detail, such as individual rebar and small conduits, but at shallower depth. These are used for concrete scanning.
  • Lower-frequency antennas reach deeper into the ground but show less detail. These are used for utility locating.

That’s why concrete scanning and utility locating use different equipment, even though both are GPR.

Why depth changes: the material

Radar loses strength as it travels. How fast depends on the material:

  • Dry materials let radar travel further.
  • Water slows and weakens the signal.
  • Clay and salts absorb radar quickly, which limits depth the most.
  • Dense rebar reflects much of the signal near the surface, which can hide objects in a lower layer.

In BC, conditions change a lot from site to site. Sandy and gravelly ground can give good depth, while silty, wet and clay-rich soils, common in parts of Richmond, Delta and the Fraser Valley, reduce it. For more on weather, read Scanning in the Rain: Can GPR Work in Wet Conditions?

What this means for concrete scanning

For most coring, cutting and anchoring jobs, GPR covers the full depth that matters. A few cases need extra care:

  • Thick slabs, mat foundations and transfer slabs, where the bottom layer may be beyond reliable range from one side
  • Two tight layers of rebar, where the top layer can mask what’s below
  • Freshly poured or very wet concrete, which reduces depth

In these cases, we may scan from both sides, adjust core locations to clear areas, or note reduced confidence in your results. Always read those notes. See Why You Need to Read Your Scan Report Carefully Before Coring or Cutting.

What this means for utility locating

Most buried services, such as power, gas, water and telecom, sit within the first one to two metres, which is within GPR’s reach in many soils. Where the ground limits GPR, we use electromagnetic locators as well. These trace metallic lines and tracer wire regardless of soil type, so the two methods together cover far more than either one alone.

How accurate is the depth?

GPR estimates depth from how long the signal takes to return. Because speed changes with the material, the technician calibrates on site, for example against a known bar, a slab edge or an exposed pipe. Depths are a close estimate, not an exact measurement, so always hand dig or core with care near any marked object.

Frequently asked questions

Can GPR see through a whole slab? For most suspended slabs and slabs on grade, yes. For very thick or heavily reinforced concrete, we’ll tell you on site if part of the depth is uncertain.

Can GPR find a pipe 3 metres down? In dry, sandy ground, often yes. In wet clay, usually not with GPR alone. Electromagnetic locating may still find it if it is metallic or has tracer wire.

Does rain make GPR shallower? In soil, it can. Indoor concrete scans are not affected.

Will you know the depth limit before you start? We can usually estimate it from the slab type or site location. The real answer comes in the first few minutes of scanning, and the technician will tell you.

Book a scan

Not sure if GPR will reach the depth your job needs? Send us the details and we’ll advise before we book.

Book a scan or call (778) 302-0868.

Leave a Reply

Your email address will not be published. Required fields are marked *

Call (778) 302-0868 Book a Scan